List of Radio Control
for HAM - Switchbox IC-SWL, RC-SWL, RC-HAM
and MARINE-Switchbox PCR-1000 & Nauticom		 
For junctions on see Junction-Diagram-List.
List of radio control and bonito switchbox
Radio / receiver / transceiver IC-SWL switchbox (RX-HAM) RC-SWL switchbox (RX-HAM) RC-HAM switchbox (TX-HAM) IC-PCR switchbox (Marine) NautiCom switchbox (Marine)
AOR-3000A / 3030 / 5000 / 7030 / 8200 - X X - X
DRAKE X - - X -
ICOM IC-PCR-1000 X X X X -
ICOM IC-XXX for CT-17 Intervace X X X - X
ICOM IC-M710 X X X - X
ICOM (the rest of all re- and trans-ceiver) X - X - X
JRC NRD-525 / 535 / 545 - X X - X
KACHINA 505 DSP X - - - -
Kenwood all like R5000 or TS-50,440,450,690,790,850,950 etc.... - X X - X
LOWE HF-150 / 225 / 250 - X - - X
SEA 235 - X - - -
SKANTI TRP- 7 / 8 / 9000 - X X - X
WINRADIO all  (Important-Info) X X - - -
Yaesu CAT all like FRG100,8800                   FT100,736R,767GX,840,847,890,900,920,980,990.1000... etc.. - X X - X 
IC-SWL	is only for HAM and for Radios like ICOM, DRAKE, KACHINA

RC-SWL	is only for HAM and all other radios
	and special for:	
		Lowe HF150, 
		Yaesu CAT 
		Icom CT-17 remote jack

RC-HAM	is only for HAM and all other tranceiver  (and only for transmitting) 
	and special for:	
		Kenwood IF10 or IC10 Interface
		Yaesu CAT  
		Icom CT-17 remote jack

IC-PCR-1000 is only for MARINE and ICOM PCR-1000

NautiCom is for MARINE and NMEA-Control

You need a special radio control for a different radio ? 
We can do that and create a new driver! 
But i need the radio for testing the new control-software.
Connection and List of ICOM-Radio
for HAM - Switchbox IC-SWL, RC-SWL, RC-HAM
and MARINE-Switchbox PCR-1000 & Nauticom

In the BONITO directorys you can find a init-file called MRX.INI, RC60.ini or RECCTL.IN.
This file included the variables: ICOM_RADIO, RECEIVER and ICOM_CONTROLLER. 
You can change this - also for unknown future icom radios. 

LIST of ICOM receiver and transceiver for Bonito Switchboxes and variables 
in init-file MRX.INI or RECCTL.INI
Type of Radio ICOM_RADIO = RECEIVER = ICOM_CONTROLLER =
ICOM IC-PCR-100  not used 22 not used
ICOM IC-PCR-1000  not used 12  not used
ICOM IC-706 72 10 224
ICOM IC-706 MKII 78 10 224
ICOM IC-706 MKIIg 88 10 224
ICOM IC-707 62 10 224
ICOM IC-M710 not used 11 not used
ICOM IC-725 40 10 224
ICOM IC-726 48 10 224
ICOM IC-728 56 10 224
ICOM IC-729 58 10 224
ICOM IC-735 4 10 224
ICOM IC-736 64 10 224
ICOM IC-737/A 60 10 224
ICOM IC-738 68 10 224
ICOM IC-746 86 10 224
ICOM IC-756 80 10 224
ICOM IC-761 30 10 224
ICOM IC-765 44 10 224
ICOM IC-775 70 10 224
ICOM IC-781 38 10 224
ICOM IC-275A/E/H 16 10 224
ICOM IC-375A 18 10 224
ICOM IC-475A/E/H 20 10 224
ICOM IC-575A/H 22 10 224
ICOM IC-820H 66 10 224
ICOM IC-970A/E/H 46 10 224
ICOM IC-1275A/E 24 10 224
ICOM IC-R72 50 10 224
ICOM IC-R75 90 10 224
ICOM IC-R7000 8 10 224
ICOM IC-R7100 52 10 224
ICOM IC-R8500 74 10 224
ICOM IC-R9000 42 10 224
ICOM IC-R10 82 10 224
ICOM-Radio for CI-V-RemoteControl
for HAM - Switchbox IC-SWL, RC-SWL, RC-HAM
and MARINE-Switchbox PCR-1000 & Nauticom

Junktion direct on RC-SWL or NautiCom switchbox - (this replaced CI-V Iinterface CT-17).
HAM: If you use a original ICOM-CI-V Interface CT-17 - its better to use the IC-SWL Switchbox.
Junctions RC-SWL or NautiCom to the icom-radio rear panel remote jack:

Bonito-switchbox................................ICOM-remote jack
Pin-5 ............... GND .........................  jack-plug-shank    
Pin-6 ......... Receiver controling ...-.......  jack-plug-head

For junktions on see Junktion-Diagram-List.

LIST of ICOM for RC-SWL / RC-HAM or NautiCom Switchbox and variables 
in init-file MRX.INI or RECCTL.INI
Type of Radio ICOM_RADIO = RECEIVER = ICOM_CONTROLLER =
ICOM IC-706 72 10 224
ICOM IC-706 MKII 78 10 224
ICOM IC-706 MKIIg 88 10 224
ICOM IC-7000 104 32 224
ICOM IC-707 62 10 224
ICOM IC-725 40 10 224
ICOM IC-726 48 10 224
ICOM IC-728 56 10 224
ICOM IC-729 58 10 224
ICOM IC-735 4 10 224
ICOM IC-736 64 10 224
ICOM IC-737/A 60 10 224
ICOM IC-738 68 10 224
ICOM IC-746 86 10 224
ICOM IC-756 80 10 224
ICOM IC-761 30 10 224
ICOM IC-765 44 10 224
ICOM IC-775 70 10 224
ICOM IC-781 38 10 224
ICOM IC-275A/E/H 16 10 224
ICOM IC-375A 18 10 224
ICOM IC-475A/E/H 20 10 224
ICOM IC-575A/H 22 10 224
ICOM IC-820H 66 10 224
ICOM IC-970A/E/H 46 10 224
ICOM IC-1275A/E 24 10 224
ICOM IC-R72 50 10 224
ICOM IC-R75 90 10 224
ICOM IC-R7000 8 10 224
ICOM IC-R7100 52 10 224
ICOM IC-R8500 74 10 224
ICOM IC-R10 82 10 224
Conventions for Bonito
angreement for Bontio Radio-Control
for all Switchboxes and INIT-Files

Variable RECEIVER = ??     = Bonito intern receiver number.
BONITO standard BAUDRATE = 4800 BAUD

BONITO variable RECEIVER
Receiver in MRX.INI (HAM) in RECCTL.INI (MARINE)
no remote controlled Receiver 0 0
AOR AR-3000A / 3030 4 4
AOR AR-5000 5 5
AOR AR-7030 6 6
AOR AR-8200 21 21
DRAKE 15 15
Icom IC-XXX 10 10
Icom IC-M710 11 11
Icom IC-PCR100 22 22
Icom IC-PCR1000 12 12
Icom IC-746 14 14
Icom 8500 26 --
JRC NRD-525 16 16
JRC NRD-535 8 8
JRC NRD-545 17 17
KACHINA 505 DSP 24 --
Kneisner+Doering KWZ 30 25 --
all Kenwood like R5000, TS-50,440,450,570 etc... 9 9
Lowe HF-150 1 1
Lowe HF-225 2 2
Lowe HF-250 3 3
SEA 235 27 27
SKANTI TRP7000/8000/9000 13 13
WINRADIO all  (Important-Info) 28 --
Yaesu FRG-100, FT-100,840,890,920,990,1000 7 7
Yaesu FT-847, FT-736R 18 18
Yaesu FT-900 23 23
Yaesu FT-980, FT-767GX 19 19
Yaesu FRG 8800 20 20

all values decimal (not HEX) 
ICOM_RADIO = Icom CI-V-Adresse (1-127) ICOM_CONTROLLER = Icom Controller Adress (default = 224)

ICOM-CI-V-Control
The bonito-radio-control operated with a 4 byte frequency-data-protocol. If the ICOM-receiver or tranceiver conneted for a 5 byte frequency-data-protocol, then you must change the operating frequency data lenght to 4 bytes.

 

 

(c) 2000 BONITO Germany

Web: www.bonito.net      email: info@bonito.net